Products : Legacy Products : ADP15-SP16 Indicator and Controller with up to 16 set points

ADP15-SP16 Indicator and Controller with up to 16 set points

ADP15-SP16.

Features

  • Up to 16 Set Points, programmable from ADP15 keypad
  • 4 and 8 relay DIN rail module
  • Individual set points & hysteresis values
  • Selectable set point quality
  • Relay contact rating 230V @ 5A AC
  • PID Control
  • Programmable output actions

The DIN rail mounted remote relay units offer an increased number of set points over that provided by a standard ADP15 indicator/controller. This allows for multi action operations.

The software of the ADP-SP16 gives the user freedom to program the number of set points for their requirements. A single ADP-SP16 will control up to 16 set points, programmed from its front panel. Set points can be individually set up with In Flight compensation and hysteresis values. Separate 'Output Latch' and 'Output Action' for up to 14 of the 16 set points is available, settable from the front panel of the ADP-SP16. A special mnemonic allows the user to specify the number of set points to be used.

A DIN rail mounted power supply unit is required where more than 4 set points are to be used. The units are driven from the ADP-SP16 via an internal special remote driver board. All relays are pluggable and connections are made via field screw terminals.


Outputs include:-
Analogue voltage and current, Industry standard digital communications, Relays, Printer Drive

Options and Accessories include:-
Panel mounting via DIN rail mounting, Power supplies for 110/230 V AC or 9-32V DC, Communications for Printer, PLC or PC.

Software Options include:- Power Factor Printers DP data only and TDP for real time/date. Printers DP data only and TDP for real time/date.

Specification

Input Type

Details

Calibration Automatic digital by use of keypad and 1 (or 2) known weights. Manual calibration can also be selected
Auto Tare By pressing keys b and then 'R' , display will zero. Auto tare value can also be viewed and manually changed if required. Auto tare value is retained on power down.
Sensitivity Preset via DIL switches between ±0.5 to ±200mV/V
Excitation 10V DC nominal, 150mA maximum
Compensation By ± sense wires to compensate for cable, connection volt drops and any variation in 10V supply
Accuracy 90 days ± 0.08% of reading ± 0.05% of FS typical
Drift 0.002%ºC typical @ 2.5mV/V

DC Analogue Outputs

Details

Order code

0 to 10V   V4
4-20mA   A3
     

Other Information

Accuracy Typical ± 0.08% of output, ± 0.08%FSD
Resolution As display resolution, max 15 bits
Calibration By 15-turn pre sets for gain and offset
Inversion By keypad value
Isolation ±130V RMS or DC max to analogue input or to any other port
Ranging Fully keypad scalable over desired display range

Communications Port

Details

Order code

RS485/232 RS485 - For up to 32 instruments on 1 bus, 4 wire 
RS232 ­ printer or direct connection to 1 device, 3 wire
COM 1

Other Information

Baud rates 300, 600, 1200, 2400, 4800, 9600 (19200 MANTRABUS only)
Electrical isolation ±130V RMS or DC max to analogue input or any other port
Formats MODBUS RTU, MANTRABUS and printer output formats
Cable Length 1km (depending on baud rate)

Alarm/Control Outputs

Details

Order code

SPCO 4 relay module REM4
SPCO 8 relay module (PSU required) REM8
PSU Power supply for REM8 module REMPSU
REM cable REM to REM cable (req. for additional REM units) REMC2

Other Information

Relays 230V at 5A AC resistive
Isolation ±130V RMS
Keypad Programmable Hysteresis, Latching, Output Inversion.

Power Supplies

Details

Order code

240 220V-230V AC 50-60Hz 10W 240
110 110V-120V AC 50-60Hz 10W 110
12 &24V 9-32V DC 10W isolated 12/24

Mounting Type

Order code

Front Panel P
Din Rail Adaptor D

Communication Port CP Operation

All display data can be accessed via the communications port along with relay and EEPROM status. All user configurable data can be changed including EEPROM enable/disable and relay reset (address code cannot be changed).

Other Options & Accessories

20mA PC Communications Interface (IF25)
VisualLink PC SCADA Software
Analogue Totaliser (Integrator)

Base ADW15

Input Filter Programmable to average up to 64 display updates.
Displays 7 segment LED 4.5 digit 10mm.3 x 3mm LED's 2 for relay status, 1 for program and hold indication.
Update Rate Up to 10 updates per seconds

Controls

4 membrane panel keys Scroll key to view/update parameter.
  Digit select key.
  Digit increment key.
  Reset key.
  Keypad disable by internal links behind front panel.
  Hold function by digit select key when in input mode.

Data Retention/Protection

Retention 10 years for set up values, minimum of 100,000 write cycle
  Protection of data and function(s)Watchdog timer giving repeat auto resets.
  Impending power detection and hold off.
  Keypad security and time out.

CE & Environmental

Storage temperature -20 to +70ºC
Operating temperature -10 to 50°C
Relative humidity 95% maximum non condensing
Safety/Low Voltage Directive 2006/95/EC
EMC Directive 2004/108/EC

Physical

Case Dimensions DIN 72 x 72 x 163mm (excluding mounting terminal)
Case Material Grey Noryl, flame retardant
Weight 750 grams
Terminals 2.5mm, saddle field terminals
Accessibility All electronics removable through front panel leaving field wiring and case in situ.

Dimensions

adp15-sp16 drawing

Downloads

Click to download - ADP15-SP16 Datasheet

Click To download - ADP15 Instruction Manual

Click to download - ADP15-SP16 Supplimentary Instruction Manual

Suggested Instrumentation

SGA Strain Gauge Analogue Amplifier

LCA15 Intelligent Strain Gauge Amplifier/Controller

ICA "In-Cell" Analogue Strain Gauge Amplifier

Options

There are currently no options available to view from this page. To view the various input and output options available for the ADP15-SP16, please view the ADP15-SP16 product datasheet by clicking here.

Applications

  • Crane safety remote display and control
  • Batch control
  • Multiple motor/pump control

Buy Now

Contact Us
Back to ListingPreviousNext

Copyright © 2017 LCM Systems
Unit 15, Newport Business Park, Barry Way, Newport Isle of Wight, PO30 5GY United Kingdom VAT no (GB 785 3956 71) and Co. Reg (2057541).

Powered By Intergage